Table size: 16" wide x 3-3/4" deep, Travel (X axis): 8", Cross slide travel (Y axis): 4"
Headstock travel(Z axis): 7", Clearance(spindle to table-top): 11", Center of spindle to face of column: 6"
Spindle speed: variable 0 to 2,500 rpm, Spindle taper: MT-3, includes 1/2 inch drill chuck and drawbar
Motor: 350 watt (0.47 hp) DC Winding is 20ohms with high/low speed plastic gear transmission
2 carbon brushs 7.8 mm wide, 4.9 mm thick, and 15 mm long. The lead wire is 25 mm long. Plastic cover is 11.6mm
Column angle: tilts from -45 degrees to +45 degrees
Overall size: 30 inches high x 20 inches deep x 20 inches wide
Weight: 110 pounds (basic machine without accessories).
FC350BJ fan-cooled 110v power supply with feedback-sensing power boost circuitry.
Purchased from Micro-Mark

6" (150 mm) range
0.0005" (0.01 mm) resolution
0.001" (0.02 mm) accuracy
Reads inches or mm
Purchased from LittleMachineShop.com

6 piece HSS end mill set
4 flute end mills
Center cutting end mills
Includes 1/8", 3/16", 1/4", 5/16", 3/8", 1/2" end mills
All end mills have 3/8" shank.
Purchased from LittleMachineShop.com

Dial test indicator with 0.0005" graduations
Range is 0.030" in either direction
Includes 5/32" and 3/8" diameter posts, dovetails on the back and end, and an 0.080" diameter point
Dial test indicator comes in a fitted case
7 jewel movement
Purchased from LittleMachineShop.com

50lb magnet
Base dimensions: 1-7/16 x 1-13/64 x 1-13/32"
Central locking mechanism with On/Off magnet power switch.
Accepts all AGD type dial indicators and test indicators
9" Reach
Purchased from amazon.com 12/2015

The jaws are 100mm (3.94") wide, 0.88" deep and open to 3.23" capacity.
The vise is 10.50" long.
The base of the vise is 200 mm by 90 mm. The slots are 12 mm wide. The slots are 80 mm apart, and there is 40 mm between the radiused ends of the slots.
Purchased from LittleMachineShop.com

Set of ten pairs of thin parallels in a fitted case
Parallels are 1/8" thick and 6" long
Heights are 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", and 1-5/8"
Made of high grade alloy steel hardened to 52 to 58 Rc
Parallel within 0.0002" on the top and bottom. The pairs are matched in height within 0.0004"
Purchased from LittleMachineShop.com

This is the removable cover that protects the top of the spindle.
I'm working on a rpm tach project that will use this as the enclosure.
Will have more info here when its moved from prototype to implementation
Purchased from LittleMachineShop.com

Includes eleven ER-32 collets
3 Morse taper shank
3/8"-16 drawbar thread
Includes spanner wrench and fitted case
Includes 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", and 3/4"
Purchased from LittleMachineShop.com

This drawbar fits the Grizzly G8689 and the Micro-Mark 82573 mini mills with the 3 Morse taper spindle, and is for use with collets and end mill holders with 3/8-16 NC thread.
Purchased from LittleMachineShop.com

3/8" diameter combination edge and center finder
The edge finder end has a 0.200" diameter cylinder
The edge and center finder is hardened and ground all over.
Purchased from LittleMachineShop.com Usage schematic Pic

This wiggler center finder set comes with 4 probes for finding centers, edges, and indicating.
Each probe snaps into the body without removing the collet nut.
The wiggler shank is 0.375" in diameter.
Purchased from LittleMachineShop.com Usage schematic Pic

This set includes 5 different sizes of combined drills and countersinks, commonly called center drills.
The set is high speed steel and includes sizes 1,2,3,4, and 5. These are 60 degree center drills.
Purchased from LittleMachineShop.com

20 piece Center cutting TiN coated HSS end mill set, Includes both 2 flute and 4 flute end mills
3/16" to 3/4" by 16ths
The 3/16" through 7/16" end mills have a 3/8" shank.
The 1/2" and 9/16" end mills have a 1/2" shank.
The 5/8" and 11/16" end mills have a 5/8" shank.
The 3/4" end mill has a 3/4" shank.
Purchased from LittleMachineShop.com

52-piece clamping kit
This clamping kit fits the 12 mm T-slots on the mini mill.
24 3/8-16 studs, 6 step block pairs, 6 T-slot nuts
6 flange nuts, 4 coupling nuts, and 6 end hold downs.
Purchased from LittleMachineShop.com

This 41-piece tap and die set includes all the common sizes from 3 mm to 12 mm.
The set includes a screw pitch gage, a die stock and a T-handle tap wrench.
The threads covered include:
mm: 3x0.50, 3x0.60, 4x0.70, 4x0.75, 5x0.80, 5x0.90, 6x0.75, 6x1.00, 7x0.75, 7x1.00, 8x1.00, 8x1.25, 10x1.25, 10x1.50, 12x1.50, 12x1.75
NPT: 1/8"-27
Purchased from LittleMachineShop.com

These precision 1-2-3 blocks are ground and case hardened on all sides to 50-60 Rc.
They are parallel within 0.0002", flat within 0.0002" and square within 0.00021".
The blocks have 23 holes through them, 5 are threaded 3/8-16 NC.
Purchased from LittleMachineShop.com

Made in USA, Surface treated black finish, Heavy duty 135degree split point
29 Piece high speed steel drill set. Set includes 1/16" - 1/2" by 64ths.
These are screw machine length drills with straight shanks.
Includes a Huot metal index for storing the drills.
Purchased from LittleMachineShop.com

These precision V-blocks are made of hardened steel.
They are ground square, parallel and concentric within 0.0001".
The V-blocks are supplied in matched pairs.
Purchased from LittleMachineShop.com

Includes the following sizes: 5/8", 11/16", 3/4", 1", & 1-3/16".
Also included is a burring reamer.
All precision machined of top grade steel.
Purchased from Ocean State Electronics

pillar, half-round, knife, three-square, round, and barrette.
Length is 5-1/2"" with #2 cut.
Comes in vinyl pouch.
Purchased from Stanley Supply & Services

coated with Black Oxide to resist loading,rust & corrosion
8 in. Flat Bastard - Premium Black Oxide Finish
8 in. Half Round Bastard - Premium Black Oxide Finish
8 in. Round Bastard - Premium Black Oxide Finish
Purchased from Sears

Base swivels 180 degrees. Jaw opens 5" Has V-grooves.
Reversible jaw faces: smooth on one side for no-mar gripping and serrated on the other side for a secure hold.
Throat size is 1/8 to 2-1/2 in. and pipe depth is 3-7/16 in.
Purchased from Sears

designed to be added to an existing central vacuum system to extract smoke, dust, fumes and particles at the source.
LOC-LINE VACUUM HOSE 3" THIN WALL PVC ADAPTER, 1 PC, WHITE
LOC-LINE VACUUM HOSE KIT, TO HOSE, 27 2.5" ELEMENTS, SHOP VACUUM HOSE ADAPTER, 4.5" ROUND NOZZLE
the shop vacuum hose adapter is currently not in use. Purchased from ModularHose.com